DPCAV
R/C CONTROLLED TRIPLE CAMERA SWITCH (3-WAY)
| Video Switch | Solid State 3-position Relay |
| Video Bandwidth | 10MHz |
| R/C Pulse Range | Industry standard 1.0mS / 2.0mS |
| Status Indication | Red / Green LED |
| Power | 4.5 - 5.5V (provided by R/C receiver) |
| Size | 1.15 x 0.95 x 0.20 inches (29 x 24 x 5 mm) |
| Weight | 6 grams |
| Installation Instructions | Click Me! |
Features / Specifications:, ,
This R/C system activated switch allows you to remotely choose ...DPCAV
R/C CONTROLLED DUAL VIDEO SWITCH (2-WAY)
| Video Switch | Solid State SPDT Relay |
| Video Bandwidth | 10MHz |
| Video Insertion loss | 0.1dB typical |
| R/C Pulse Range | Industry standard 1.0mS / 2.0mS |
| Status Indication | Red / Yellow LED |
| Power | 4.5 - 13V / 20mA (provided by R/C receiver) |
| Size | 1.3 x 0.9 x 0.20 inches (33 x 23 x 5 mm) |
| Weight | 5 grams |
| Installation Instructions | Click Me! |
Features / Specifications:, ,
This R/C system activated video switch allows you to remotely ...DPCAV
5.8GHZ A/V TRANSMITTER, 200MW
,
SOLD OUT: No longer available. This 5.8GHz / 200mW wireless ...DPCAV
DIGITAL OSCILLOSCOPE, 1MHZ
| Note | This is the improved hardware model and it is FACTORY ASSEMBLED (it is not a kit). |
| Source Coupling | DC/AC. |
| Storage Mode | Hold/run, BMP export. |
| Sample Waveform | Click Me! |
| 500Hz test signal | Click Me! |
| Frequency Measurement | Click Me! |
| Sawtooth Waveform | Click Me! |
| FFT 100KHz Measurement | Click Me! |
| FFT Demo Video | Click Me! |
| Instruction Manual | Click Me! |
| Manufacture's Web Site | Click Me! |
New and Improved Digital Oscilloscope:, Now with higher accuracy, FFT frequency domain display, external trigger I/O, and many other new features. It has 1MHz analog bandwidth, up to 2MSa/s real-time sampling, and digital storage for freezing waveforms. This has to be the best value Digital Oscilloscope on the planet!, Features:, Max sample rate - 2M/s，8 bits., Related photos:, , Useful Links:,
Included is a universal 100-240VAC 50/60Hz wall adapter with North ...DPCAV
WIRELESS VIDEO TRANSMITTER & OSD, FPV DEAL
| Item A | EagleTree eLogger V4 with 100 Amp sensor. |
| Item B | USB cable for eLogger firmware updates. |
| Item C | Eagle Tree OSD Pro Video Expander module. |
| Item D | GPS extension cable for kits shipped before June-2010. |
| Item E | eLogger GPS-V4 Expander module. |
| Item F | Eagle Tree OSD Pro cable Kit. |
| Item H | DPC-420A 420 line CCD color camera. |
| Item I | DPC-420A/480A camera interconnect cable. |
| Item J | TX9-500 900MHz / 500mW transmitter. |
| Item K | Dipole Antenna, +3dBi omni-directional. |
| Item L | Deluxe A/V cable for TX9-500 transmitter. |
| Item M | Male-male video adapter cable, |
This wireless OSD system will transmit graphic data and voice announcements that report a variety of alarms and data, including: voltage, current, mAH, Watts, Home Arrow, Return to Home (RTH / RTL), RADAR, altitude, course (travel direction), ground speed, longitude, latitude, and navigation waypoints. You can expand this system even further by using the low cost eLogger accessories, such as these:Click Me!, Here's a screen shot that shows some of the information that can be shown (temperature and RPM data requires optional accessories):, , All the data parameters that are supported by the eLogger can be displayed on the video display. Here are some examples:, , Notice: Due to the 900MHz transmitter's high RF power, using it in the USA and other countries will require an amateur/ham radio license (some countries may forbid its use). It is your responsibility to ensure that its use meets the requirements of your government’s RF spectrum regulations. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them., . We have other battery choices so that you can select the best one for your application. More choices:Click Me, (3) The 900MHz A/V receiver is not included, but we offer fully compatible models that work great with this special package. Please look here to purchase them:click here, The video format is available in NTSC or PAL. If you are unsure which to choose then please consult this list:TV Video Standards., ,
Ok, so you've decided that you need the EagleTree OSD ...DPCAV
VOLTAGE REGULATOR FOR 5VDC CAMERA
| Installation instructions | Click Me! |
Features and Specifications:, ,
This tiny 5VDC Voltage Regulator (VReg) allows a low current ...ngHobbies
1.5W 1.3GHZ TRANSMITTER
Features:, Frequency Band:, 1280MHz Locked, Number of Channels:, 1, Audio Sub-carrier:, 5.5MHz, Transmission Range:, 1800 Meter plus, Power Consumption:, 600mA, Output Power:, 1500mW, Operation Voltage:, 12, Power Supply:, 12V/750mA, Antenna Connector:, SMA Connector, Weight:, 30 g, Dimensions:, 70 x 25.7 x 8 mm, Documentation:, , Warranty:, 3 months, Note:, ** The power level of this transmitter may be illegal in your country. Please check your local regulations and make sure you order this device only if you have the required licensing to use this product.,
Highly integrated 1.3 GHz transmitter. These transmitters are locked on ...ngHobbies
IPHONE INTERFACE CABLE
| Weight | 15g |
| Cable length | 2ft or about 60cm |
| http | //www.immersionrc.com/itelemetry |
Specifications:, Plug and play with most receivers., Documentation:, Click here, iPhone Application:, ,
The iPhone interface cable is a companion to the EzOSD ...ngHobbies
EZUHF 8CH RECEIVER
| Width | 28mm |
| Height | 20mm |
| Length | 70mm |
| Weight | 20 grams (without antenna) |
Notice:, , Dimensions:, , Content of the pacakge:, 1 x EzUHF 8 channel Receiver, Note:, , Documentation:, , Support thread on RcGroups:,
The EzUHF 8-ch receiver which supports a diversity antenna configuration, ...ngHobbies
GOPRO CAMERA MOUNT FOR MK HEXA/OKTO
This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, Demo Videos:, Outdoor testing - click here, Note:, This kit comes with a mounting plate which either replaces of can be sandwitched under the battery holding plate on Hexa and Optokopters. Additional mountig plates for Quads will be available soon., Assembly documentation:, Click here to open or download (2Mb),
New Generation Hobbies is proud to present this low cost ...ngHobbies
DRAGONOSD+ V2 COMBO
| Width | 29mm |
| Height | 12mm |
| Length | 50mm |
| Weight | 10 grams (OSD only) |
Display Features:, Voltage measurement:, 2 ports available, Current measurement:, 1 port available, GPS sensor provides:, Altitude, Ground speed, Coordinates, Number of satellites, Heading indicator, Home direction, LOS Distance, Distance to home, Barometric sensor provides:, Altitude, Temperature, Variometer:, Airspeed, Vertical speed indicator, Compass:, Magnetic heading indicator, IMU:, Artificial Horizont, Other features:, Elapsed time, Callsign, RSSI, Flight summary, Various display modes, Remote OSD off, Configurable border area, Configuration:, On screen menu, Configure via stick input, Configure via PC, Customizable screen layout, Alerts:, Range, Altitude, Stall speed, Voltage, mAh, Audio notification, Lost signal, RSSI level, Integration:, Single servo wire link from the DragonLink for multi-channel auto-pilot, Logging:, Google Earth Logging, Autopilot:, RTH (Return to home), IMU fly-by-wire, Wayppoints:, 20 GPS way points configurable on the PC, Hardware:, PAL/NTSC auto-detect, GPS auto-detect, UART interfaces, I2C extension bus (various devices supported), This OSD package contains the following items:, Main DragonOSD+ V2 board, Dimensions:, , Documentation:, Click here, Connection schematics:, Click Here, Firmware upgrades and download PC software:, Click here,
New Generation Hobbies is happy to bring you the new, ...ngHobbies
SKYWALKER FPV PAN/TILT POD KIT
| Comes with a mounting plate that will fit many popular FPV cameras including | KX131, KX171, KX191, IF Cam, SN777, SN555 and many others |
| Instructions to build the pan and tilt | Coming Soon |
Note:, careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include*:, Laser cut components for the main pod, You'll need to supply:, Double sided servo tape to apply TX, camera, and tilt servo., Documentation:,
A SkyWalker FPV pod that uses a custom mechanism allowing ...ngHobbies
5VOLT 2 CHANNEL VIDEO SPLITTER V2
,
For the ultimate diversity system, New Generation Hobbies brings you ...